Steps to install service pack 1. STEP 1: Install latest firmware and drivers. --a. Navigate to D:\rs-pkgs\SP1UpgradeSteps\step1 and run suulauncher.exe. --b. Once the program initlizes please apply all updates. --c. If you get disconnected due to broadcom drivers being installed then log back onto the server and re-run the program. --d. When asked to reboot please do so. --e. After reboot please re-run the program to ensure that all updates have applied. --f. If there are still some out-standing please re-run and reboot until all are done. --NOTE: Sometimes this program fails. If it does you can see the list of updates that need to be applied and manually apply them. They are located inside the "repository" directory. Run each seperately being sure to keep the BIOS until the very last. You can apply all and only reboot ONCE assuming you save BIOS for last. Re-Run the program to ensure ALL updates were applied. STEP 2: Uninstall and Install of Dell Open Manage --a. Uninstall: Go to add/remove programs in control panel and click "remove" on Dell Open Manage. --b. Install: Open task manager (right click on the start bar and go to 'task manager'), display all process, and endtask on CCMExec. --c. Navigate to D:\rs-pkgs\SP1UpgradeSteps\step2 and run setup.exe. --d. Look at the information displayed and see if there are any alerts that have to be handled PRIOR to installing (should be listed with red exclamation marks). --e. Fix any that need to be resolved prior to proceeding. --f. Once these are fixed you should be able to select all defaults and click install. --g. Reboot when requested. --h. After reboot please confirm the latest OM is working as expected. --NOTE: If for some reason uninstall fails please reboot and navigate to D:\rs-pkgs\SP1UpgradeSteps\OMClean and run OMClean.exe. Reboot after running this program and re-try the install. Sometimes you have to run this four or five times before OM will install properly. STEP 3: Install Latest Legato Agent --a. Check the version of networker by starting legato and going to "help" --> "about". --b. It should be version 7.1.3 or newer. --c. If it is older please uninstall using add/remove programs. --d. If the sql agent is installed then uninstall it as well. --e. Go to D:\rs-pkgs\SP1UpgradeSteps\step3 and run nw713_win_x86.exe --f. Install with defaults and specifying the datacenter when requested. (See below). --g. At the end of the installer be sure to turn OFF 'Launch Legato NetWorker Module Permissions Wizard'. --h. If it had the SQL agent then please run nmsql41_win_x86.exe (located in step3) following the same procedure listed above. --NOTE: If the install fails then please cancel the install and navigate to C:\program files\legato and delete all contents, then re-run the installer. IAD ===== networker1-adv1.iad1.storage.rackspace.com networker1a-adv1.iad1.storage.rackspace.com networker1b-adv1.iad1.storage.rackspace.com ===== DFW ===== networker1-adv1.dfw1.storage.rackspace.com networker1a-adv1.dfw1.storage.rackspace.com networker1b-adv1.dfw1.storage.rackspace.com ===== LON ===== networker1.lon.storage.rackspace.com nw1a.lon.storage.rackspace.com nw1b.lon.storage.rackspace.com ===== SAT2 ===== networker1.sat2.rackspace.com ===== Step 4: Install SAN updates. --a. Install SAN updates as per the document from James Howard. STEP 5: Install SP1 --a. Go to D:\rs-pkgs\SP1UpgradeSteps\step5 and run WindowsServer2003-KB889101-SP1-x86-ENU.exe --b. Follow all defaults. --c. Reboot when requested. --d. Log into the server and confirm SP1 installation. Step 6: Delete install files --a. Please navigate to D:\rs-pkgs\ and delete the SP1UpgradeSteps directory.