######################################################################

DELL OPENMANAGE(TM) SERVER ASSISTANT VERSION 8.9 README

######################################################################

NOTE: This readme provides information about Dell OpenManage Server
      Assistant version 8.9.

You can run Dell OpenManage Server Assistant from the "Dell PowerEdge
Installation and Server Management" CD and is sometimes referred to as
Server Assistant Media within the application. This version of 
Server Assistant is located in the "Dell(TM) PowerEdge(TM)
Installation and Server Management" CD that provides the tools you 
need to configure your system and install your operating System. For 
the latest version of this readme, see the Dell Support website at
"support.dell.com." 

######################################################################
TABLE OF CONTENTS
######################################################################

This file contains the following sections: 

* Criticality

* Minimum Requirements

* Release Highlights

* Installation

* User Notes 

* Known Issues

######################################################################
CRITICALITY
######################################################################

3 = Optional

Dell recommends that you review specifics about the update to 
determine if it applies to your system. The update contains changes
that impact only certain configurations, or provides new features 
that may or may not apply to your environment.

######################################################################
MINIMUM REQUIREMENTS
######################################################################

This section provides information about the supported systems, 
operating systems, and system requirements for Server Assistant.

======================================================================
SUPPORTED SYSTEMS
======================================================================

* The following PowerEdge systems are supported on the "Dell 
  PowerEdge Installation and Server Management" CD version 8.9: 600SC,
  650, 700, 750, 800, 830, 840, 850, 860, 1600SC, 1650, 1655MC,
  1750, 1800, 1850, 1855, 1900, 1950, 1955, 2600, 2650, 2800, 2850,
  2900, 2950, 4600, 6600, 6650, 6800, and 6850.

======================================================================
SUPPORTED OPERATING SYSTEMS
======================================================================

The following operating systems are supported: 

* Microsoft(R) Windows(R) 2000 Server (SP4) 
* Microsoft Windows Server(R) 2003, SBS (SP1, R2) 
* Microsoft Windows Server 2003 x64 Edition, R2
* Red Hat(R) Enterprise Linux (version 3) Update 6 for Intel(R) x86
* Red Hat  Enterprise Linux (version 3) Update 6 for Intel(R) EM64T
* Red Hat Enterprise Linux (version 4) for Intel x86
* Red Hat Enterprise Linux (version 4) for Intel EM64T
* SUSE(R) LINUX Enterprise Server version 9 (SP3) x86_64
* SUSE LINUX Enterprise Server version 10 x86_64

======================================================================
SYSTEM REQUIREMENTS
======================================================================

The following system requirements are required to run Server 
Assistant:

* Minimum 128 MB of random access memory (RAM)
* Minimum 512 MB of random access memory (RAM) for SUSE LINUX 
  Enterprise Server  versions 9 and 10 installation
* Hard drive requirements will vary according to the operating system
  installed

######################################################################
RELEASE HIGHLIGHTS 
######################################################################

* Added support for Novell SUSE LINUX Enterprise Server version 10 
  x86_64
* Added support for Windows Server 2003, SBS R2
* Added support for a stand-alone utility to extract drivers. This
  utility is available on the “Dell PowerEdge Installation and Server
  Management" CD

######################################################################
INSTALLATION
######################################################################

1. Insert the "Dell PowerEdge Installation and Server Management" CD 
   into the CD drive and reboot the system. If your system is 
   supported by the CD, the graphical user interface (GUI) 
   displays an image of the system.
 
2. Keep all configuration information for the system ready.
  
3. Click "Continue" and follow the instructions to complete the 
   installation. 
   NOTE: Context-sensitive help is provided on each page.
 
4. When prompted, insert the operating system CD. 

5. For systems running supported Windows, SUSE Linux Enterprise Server
   and Red Hat Enterprise Linux operating systems, remove the
   operating system CD from the CD drive before clicking "Finish.”

6. The system reboots and the unattended operating system 
   installation continues.
 
7. When the installation is complete, your system is ready for use.

######################################################################
USER NOTES
######################################################################

This section provides information to help enhance your experience 
with Server Assistant in particular implementations and environments.

======================================================================
GENERAL NOTES 
======================================================================

* The following languages are supported by Server Assistant:

  * English 
  * French 
  * German 
  * Spanish 
  * Simplified Chinese
  * Japanese

* For details on the driver extracting utility, see the readme.txt
  under the /server_assistant/driver_tool folder.

* The utility partition does not have DOS(R)-based RAID tools.

* If the Server Assistant GUI disappears and a blank screen is 
  displayed, restart the system. This issue occurs if you right-click
  to open a new browser window (from the "Quick Information Guide" 
  window) and select "Quit" from the "File" menu.
  
* In order to use the RAID configuration feature of Server Assistant
  to configure RAID and install the operating system, the "Fast 
  Initialization" parameter of the RAID controller must be set to 
  "ON." This setting is the factory-default of all RAID controllers.

* While using the "Dell PowerEdge Installation and Server Management"
  CD, do not insert or remove any hot-swappable drives until the
  operating system is completely installed. The results may be
  unpredictable and the installation may fail.

* Replication is supported on systems with multiple controllers, 
  provided the controllers are in an initialized state. This is 
  applicable to both master and target systems.

* If you configure RAID manually and use Server Assistant to install
  an operating system on a master system, then should manually
  configure RAID on the target system as well.

* Use local accounts for creating the Server Message Block (SMB) share
  on Windows on which the Red Hat Package Manager (RPMs) will reside
  for the network-download feature.

* If the number of hard disks is large, the "Erase All Hard Disks"
  feature under "System Tools" may take a long time to erase the
  hard disks. During the erase process, you will see the same screen
  with an hourglass display.  Wait until the operation completes and
  the system reboots.

* Server Assistant does not support the installation of tape or Fibre
  Channel drivers with the operating system installation. You can 
  download the drivers for these devices from the "Dell PowerEdge 
  Service and Diagnostics" CD, or from “support.dell.com.”
  
* The "Keyboard Type" locale option offered for a keyboard layout on
  the Server Assistant home page is for the Server Assistant screens
  navigation only.  The selected keyboard layout setting is not passed
  to the installed operating system.

======================================================================
USER NOTES FOR WINDOWS OPERATING SYSTEMS
======================================================================

* During Windows installation, the system will automatically log on
  to finish the post-installation tasks and will then automatically
  log out. It is recommended that you do not perform any task until
  the system has automatically logged out. Installation may end 
  abnormally if the installation process is interrupted. 

* The Server Setup program does not support the installation of 
  Windows 2000 and 2003 Datacenter.

* If Console Redirection is enabled, then a dialog box is displayed 
  stating that the EMS connection has been found during the operating
  system installation. 

* It is recommended that you use Windows 2000 with Service Pack 4 
  (or higher) integrated CD for the Windows 2000 installation if your
  system has the Conexant(R) modem. Otherwise, the installation of 
  Windows 2000 will stop responding while devices are being 
  installed. Reboot the system to resolve the issue.

* On Windows 2000 Advanced Server operating system, if you uninstall
  and then reinstall Cluster Service, you may get an incorrect prompt
  to insert a "Service Pack" CD. Insert the "Microsoft Windows 2000 
  Advanced Server" CD instead.

* In the Advanced "Enter OS Information" screen, enter all IP 
  addresses for the "Trap Destination" field, separated by commas. Do
  not enter trailing commas, or the installation will stop when the 
  Windows Setup program runs.

* On PowerEdge 700 and 750 servers a yellow bang occurs with USB 
  controller after the installation of the operating system is 
  complete. However, USB devices will work correctly when connected.
  
* If you install Windows Server 2003 Web Edition using Dell Server
  Assistant, IIS will be installed by default. Choose NTFS file system
  to ensure all IIS components install correctly.

======================================================================
USER NOTES FOR RED HAT ENTERPRISE LINUX OPERATING SYSTEMS
======================================================================

* At least 14.1 GB disk space is required to install Red Hat 
  Enterprise Linux.

* If you use the "Download RPMs from Network" feature, the RPMs are 
  downloaded to the partition called "/home." The recommended size for
  this partition is 3 GB plus the size of the RPMs you want to update.
  All downloaded RPMs are installed during the post install phase of
  the Red Hat Enterprise Linux installer.
   
* Entering a double quote character (") in the "Root Password" field 
  of the Red Hat Enterprise Linux installation will result in denial 
  of access to the root "log in."

* Server Assistant limits the block device size on Red Hat Enterprise 
  Linux system (version 3.0 or earlier) to 1 TB. Red Hat Enterprise 
  Linux system (version 4.0), however, allows a maximum device size 
  of 8 TB. 

* A network download of RPMs requires that the target system have a 
  Dynamic Host DHCP IP address and that the system is connected to a
  network.

* While configuring the hard drive on a system to install a Red Hat 
  Enterprise Linux operating system, if the hard drive space on your 
  system is used completely, and the range specified in the GUI 
  against the "swap" partition is the same 
  (for example [1024 -1024] MB), the scroll bar remains on the
  left side.
  

######################################################################
KNOWN ISSUES
######################################################################

The following subsections list the known issues with this release of 
Server Assistant.

======================================================================
KNOWN ISSUES FOR ALL OPERATING SYSTEMS
======================================================================

* While navigating through the Server Assistant screens, if you see 
  the “Unknown Error” message, the following could be the possible 
  reasons for this message:

  - Disks not initialized
  - Predictive or actual disk failure on one or more of the disks
  - Unsupported mix of SAS and SATA type disks
  - Controller restrictions
  - Unsupported configuration

  Take corrective action based on the above-mentioned reasons and
  restart the Server Assistant installation process.

* Server Assistant does not support RAID configuration on any system 
  with a SATA 2s controller connected to one hard drive. To 
  install Server Assistant on a system with the SATA 2s controller,
  set the hard drive configuration to "Native Mode" through BIOS or
  configure RAID through the "Ctrl+A" option.

* If a USB flash device is connected to the system, Server Assistant 
  may fail to install the operating system. To resolve the issue, 
  perform one of the following actions:

  - Remove the USB flash device.

  - In the BIOS setup, under "Boot Order," move the "USB Device"
    selection to the end of the list.

* The "View Hardware" feature in Server Assistant does not provide 
  information on devices that are connected to the chassis. The 
  current listing of devices is not complete and does not include a 
  few devices such as Fibre Channel cards, Remote Access Controller
  (RAC) 5.
  
* On PowerEdge 1800 the "View Hardware" feature in Server Assistant
  does not show the CERC SATA 2s device when it is set to ATA mode.
  This is due to the current limitation of CERC SATA 2s; it has the
  same PCI device ID for both ATA and RAID mode. 

* Use of localized special characters may cause the Server
  Assistant GUI to freeze intermittently. 

* If there are multiple SCSI or RAID controllers on the system, 
  Server Assistant will always use the controller listed first
  in the BIOS boot order list. If you want to use a particular
  controller for the operating system, set up the given controller
  as the first boot device in BIOS setup.

* Server Assistant does not support the configuration of partitions
  or the installation of operating systems on systems with PERC 2/SC,
  PERC 2/DC, or PERC 2/QC controllers or any type of Fibre Channel 
  storage adapter. 

* It is not recommended to start the server setup program if any
  virtual disks are in a failed or degraded state. Use the RAID
  controller's firmware utility (, , or 
  during boot) to reset the RAID controller's state. If an array
  disk is removed, the firmware utility may indicate the
  configuration has changed. Accepting these changes on the command
  line may not be enough; enter the firmware utility and reset the
  controller.

* On CERC ATA or CERC SATA RAID controller cards, disks that appear 
  in "Legacy" mode will not be available for RAID configuration in 
  Server Assistant. If you want to use any disk that is in "Legacy" 
  mode as part of a RAID container, you need to use the RAID 
  controller firmware utility to initialize these disks. Similarly,
  if all disks are in "Legacy" mode, then Server Assistant may fail
  to configure RAID on the controller. 

* The Server Setup program might fail if it runs when scrubbing is 
  active on a RAID virtual disk. 

* Server Assistant does not identify the boot device when PERC 
  4/DC or PERC 3/DC are in cluster mode and the adapter's BIOS is
  disabled. This will put Server Assistant in an infinite "Write Disk
  signature" and reboot loop. Use Server Assistant to install the 
  operating system on these PERC cards in a non-cluster mode.

* Server Assistant cannot detect the correct slot number of the PCI
  slots containing Adaptec RAID controllers. The message "Unknown Slot
  Number" is displayed. 

* On systems with low memory (less than 256 MB) and more than one 
  RAID controller, Server Assistant may fail during RAID 
  configuration. Install the additional adapters after the operating
  system has been installed on the first adapter.

* When using the Custom install script feature, commands that do not
  return cause the system to stop responding during booting of Red 
  Hat Enterprise Linux or while registering components on Windows 
  installations.

* On SAS 5/iR controller cards, disks that appear in "Foreign" state
  will not be available for operating system installation in non-RAID
  mode. If you want to use any disk that is in "Foreign" state for
  the operating system installation, clear the physical disks using
  "Erase All Physical Disks" feature under System Tools section. 
  If all disks are in "Foreign" state, Server Assistant may fail
  to install the operating system on the controller in the non-RAID
  mode.

* On system with SAS 5/iR controller cards connected to more than two
  disks, Server Assistant supports only Advanced RAID Configuration.
  In "Advanced" mode, it is mandatory to select the disk with the
  lowest drive ID for RAID configuration.

======================================================================
KNOWN ISSUES FOR RED HAT ENTERPRISE LINUX OPERATING SYSTEMS
======================================================================

* When using the "Dell PowerEdge Installation and Server Management" 
  CD for new RAID configurations, installation of the Red Hat 
  Enterprise Linux operating system may fail if both the USB CD and 
  USB floppy are connected. To avoid the installation failure, remove 
  the USB floppy connection before rebooting the system with the CD 
  for the installation process.

* Installation of Red Hat Enterprise Linux (version 4) operating 
  system is not supported on any system having the CERC ATA 4ch
  controllers:

  NOTE: In the above case, the option to install Red Hat Enterprise 
  Linux (version 4) will not be available on the "Select Operating 
  Systems" page.

* Installation of Red Hat Enterprise Linux (all versions) operating 
  system is not supported on any system having the following 
  controllers (irrespective of being present as boot-controllers or
  not):

  * Promise RAID
  * CERC SATA 2s in RAID mode 
  
  NOTE: In the above cases, option to install Red Hat Enterprise 
  Linux operating system will not be available on the "Select 
  Operating Systems" page. 

* The Red Hat Enterprise Linux version 3) operating system
  installation may fail on systems equipped with multiple RAID and/or
  SCSI controllers, whether installed on the system board or in PCI
  slots. This failure may occur when using Server Setup or performing
  a manual installation.  When two or more RAID or SCSI controllers
  are present, install Red Hat Enterprise Linux with only one
  configured RAID or SCSI controller. Configure the other controllers
  after you install the Red Hat Enterprise Linux operating system. 

* On the Red Hat Enterprise Linux (version 3) operating system, the 
  GUI is not available on the PowerEdge 6800 or PowerEdge 6850 system.
  This is fixed in the latest update to the "X server" package that is
  available from Red Hat. Use the Red Hat system update tools to
  download and install the latest operating system updates.

======================================================================
KNOWN ISSUES FOR SUSE LINUX ENTERPRISE SERVER (VERSIONS 9 and 10) 
OPERATING SYSTEMS
======================================================================

* The SUSE Linux Enterprise Server (versions 9 and 10) operating
  system installation may fail on systems equipped with multiple RAID
  and/or SCSI controllers, whether installed on the system board or in
  PCI slots. This failure may occur when using Server Setup or 
  performing a manual installation.  When two or more RAID or SCSI
  controllers are present, install SUSE Linux Enterprise Server 
  (version 9 or version 10) with only one configured RAID or SCSI
  controller. Configure the other controllers after you install the
  SUSE Linux Enterprise Server (version 9 or version 10) operating
  system.

* The SUSE Linux Enterprise Server (version 9) operating system
  installation may fail on systems equipped with multiple disks and
  the boot device is set to a disk that does not have the lowest port
  number. To ensure  successful installation across all supported
  operating systems, it is recommended that the boot device is set
  to the disk with the lowest port number.

######################################################################

Information in this document is subject to change without notice.
(C) 2006 Dell Inc. All rights reserved.

Reproduction in any manner whatsoever without the written permission 
of Dell Inc. is strictly forbidden.

Trademarks used in this text: "Dell," "PowerEdge," and "Dell 
OpenManage" are trademarks of Dell Inc.; "Microsoft," "Windows,"
and "Windows Server" are registered trademarks of 
Microsoft Corporation; "Novell" and "SUSE" are registered 
trademarks of Novell, Inc.; "Intel" is a registered trademark of 
Intel Corporation; "Red Hat" is a registered trademark of Red Hat,
Inc; Conexant is a registered trademark of Conexant Inc. 

Other trademarks and trade names may be used in this document to refer 
to either the entities claiming the marks and names or their products.  
Dell Inc. disclaims any proprietary interest in trademarks and 
trade names other than its own.

July 2006