###################################################################### DELL OPENMANAGE(TM) SERVER ASSISTANT VERSION 8.9 README ###################################################################### NOTE: This readme provides information about Dell OpenManage Server Assistant version 8.9. You can run Dell OpenManage Server Assistant from the "Dell PowerEdge Installation and Server Management" CD and is sometimes referred to as Server Assistant Media within the application. This version of Server Assistant is located in the "Dell(TM) PowerEdge(TM) Installation and Server Management" CD that provides the tools you need to configure your system and install your operating System. For the latest version of this readme, see the Dell Support website at "support.dell.com." ###################################################################### TABLE OF CONTENTS ###################################################################### This file contains the following sections: * Criticality * Minimum Requirements * Release Highlights * Installation * User Notes * Known Issues ###################################################################### CRITICALITY ###################################################################### 3 = Optional Dell recommends that you review specifics about the update to determine if it applies to your system. The update contains changes that impact only certain configurations, or provides new features that may or may not apply to your environment. ###################################################################### MINIMUM REQUIREMENTS ###################################################################### This section provides information about the supported systems, operating systems, and system requirements for Server Assistant. ====================================================================== SUPPORTED SYSTEMS ====================================================================== * The following PowerEdge systems are supported on the "Dell PowerEdge Installation and Server Management" CD version 8.9: 600SC, 650, 700, 750, 800, 830, 840, 850, 860, 1600SC, 1650, 1655MC, 1750, 1800, 1850, 1855, 1900, 1950, 1955, 2600, 2650, 2800, 2850, 2900, 2950, 4600, 6600, 6650, 6800, and 6850. ====================================================================== SUPPORTED OPERATING SYSTEMS ====================================================================== The following operating systems are supported: * Microsoft(R) Windows(R) 2000 Server (SP4) * Microsoft Windows Server(R) 2003, SBS (SP1, R2) * Microsoft Windows Server 2003 x64 Edition, R2 * Red Hat(R) Enterprise Linux (version 3) Update 6 for Intel(R) x86 * Red Hat Enterprise Linux (version 3) Update 6 for Intel(R) EM64T * Red Hat Enterprise Linux (version 4) for Intel x86 * Red Hat Enterprise Linux (version 4) for Intel EM64T * SUSE(R) LINUX Enterprise Server version 9 (SP3) x86_64 * SUSE LINUX Enterprise Server version 10 x86_64 ====================================================================== SYSTEM REQUIREMENTS ====================================================================== The following system requirements are required to run Server Assistant: * Minimum 128 MB of random access memory (RAM) * Minimum 512 MB of random access memory (RAM) for SUSE LINUX Enterprise Server versions 9 and 10 installation * Hard drive requirements will vary according to the operating system installed ###################################################################### RELEASE HIGHLIGHTS ###################################################################### * Added support for Novell SUSE LINUX Enterprise Server version 10 x86_64 * Added support for Windows Server 2003, SBS R2 * Added support for a stand-alone utility to extract drivers. This utility is available on the “Dell PowerEdge Installation and Server Management" CD ###################################################################### INSTALLATION ###################################################################### 1. Insert the "Dell PowerEdge Installation and Server Management" CD into the CD drive and reboot the system. If your system is supported by the CD, the graphical user interface (GUI) displays an image of the system. 2. Keep all configuration information for the system ready. 3. Click "Continue" and follow the instructions to complete the installation. NOTE: Context-sensitive help is provided on each page. 4. When prompted, insert the operating system CD. 5. For systems running supported Windows, SUSE Linux Enterprise Server and Red Hat Enterprise Linux operating systems, remove the operating system CD from the CD drive before clicking "Finish.” 6. The system reboots and the unattended operating system installation continues. 7. When the installation is complete, your system is ready for use. ###################################################################### USER NOTES ###################################################################### This section provides information to help enhance your experience with Server Assistant in particular implementations and environments. ====================================================================== GENERAL NOTES ====================================================================== * The following languages are supported by Server Assistant: * English * French * German * Spanish * Simplified Chinese * Japanese * For details on the driver extracting utility, see the readme.txt under the /server_assistant/driver_tool folder. * The utility partition does not have DOS(R)-based RAID tools. * If the Server Assistant GUI disappears and a blank screen is displayed, restart the system. This issue occurs if you right-click to open a new browser window (from the "Quick Information Guide" window) and select "Quit" from the "File" menu. * In order to use the RAID configuration feature of Server Assistant to configure RAID and install the operating system, the "Fast Initialization" parameter of the RAID controller must be set to "ON." This setting is the factory-default of all RAID controllers. * While using the "Dell PowerEdge Installation and Server Management" CD, do not insert or remove any hot-swappable drives until the operating system is completely installed. The results may be unpredictable and the installation may fail. * Replication is supported on systems with multiple controllers, provided the controllers are in an initialized state. This is applicable to both master and target systems. * If you configure RAID manually and use Server Assistant to install an operating system on a master system, then should manually configure RAID on the target system as well. * Use local accounts for creating the Server Message Block (SMB) share on Windows on which the Red Hat Package Manager (RPMs) will reside for the network-download feature. * If the number of hard disks is large, the "Erase All Hard Disks" feature under "System Tools" may take a long time to erase the hard disks. During the erase process, you will see the same screen with an hourglass display. Wait until the operation completes and the system reboots. * Server Assistant does not support the installation of tape or Fibre Channel drivers with the operating system installation. You can download the drivers for these devices from the "Dell PowerEdge Service and Diagnostics" CD, or from “support.dell.com.” * The "Keyboard Type" locale option offered for a keyboard layout on the Server Assistant home page is for the Server Assistant screens navigation only. The selected keyboard layout setting is not passed to the installed operating system. ====================================================================== USER NOTES FOR WINDOWS OPERATING SYSTEMS ====================================================================== * During Windows installation, the system will automatically log on to finish the post-installation tasks and will then automatically log out. It is recommended that you do not perform any task until the system has automatically logged out. Installation may end abnormally if the installation process is interrupted. * The Server Setup program does not support the installation of Windows 2000 and 2003 Datacenter. * If Console Redirection is enabled, then a dialog box is displayed stating that the EMS connection has been found during the operating system installation. * It is recommended that you use Windows 2000 with Service Pack 4 (or higher) integrated CD for the Windows 2000 installation if your system has the Conexant(R) modem. Otherwise, the installation of Windows 2000 will stop responding while devices are being installed. Reboot the system to resolve the issue. * On Windows 2000 Advanced Server operating system, if you uninstall and then reinstall Cluster Service, you may get an incorrect prompt to insert a "Service Pack" CD. Insert the "Microsoft Windows 2000 Advanced Server" CD instead. * In the Advanced "Enter OS Information" screen, enter all IP addresses for the "Trap Destination" field, separated by commas. Do not enter trailing commas, or the installation will stop when the Windows Setup program runs. * On PowerEdge 700 and 750 servers a yellow bang occurs with USB controller after the installation of the operating system is complete. However, USB devices will work correctly when connected. * If you install Windows Server 2003 Web Edition using Dell Server Assistant, IIS will be installed by default. Choose NTFS file system to ensure all IIS components install correctly. ====================================================================== USER NOTES FOR RED HAT ENTERPRISE LINUX OPERATING SYSTEMS ====================================================================== * At least 14.1 GB disk space is required to install Red Hat Enterprise Linux. * If you use the "Download RPMs from Network" feature, the RPMs are downloaded to the partition called "/home." The recommended size for this partition is 3 GB plus the size of the RPMs you want to update. All downloaded RPMs are installed during the post install phase of the Red Hat Enterprise Linux installer. * Entering a double quote character (") in the "Root Password" field of the Red Hat Enterprise Linux installation will result in denial of access to the root "log in." * Server Assistant limits the block device size on Red Hat Enterprise Linux system (version 3.0 or earlier) to 1 TB. Red Hat Enterprise Linux system (version 4.0), however, allows a maximum device size of 8 TB. * A network download of RPMs requires that the target system have a Dynamic Host DHCP IP address and that the system is connected to a network. * While configuring the hard drive on a system to install a Red Hat Enterprise Linux operating system, if the hard drive space on your system is used completely, and the range specified in the GUI against the "swap" partition is the same (for example [1024 -1024] MB), the scroll bar remains on the left side. ###################################################################### KNOWN ISSUES ###################################################################### The following subsections list the known issues with this release of Server Assistant. ====================================================================== KNOWN ISSUES FOR ALL OPERATING SYSTEMS ====================================================================== * While navigating through the Server Assistant screens, if you see the “Unknown Error” message, the following could be the possible reasons for this message: - Disks not initialized - Predictive or actual disk failure on one or more of the disks - Unsupported mix of SAS and SATA type disks - Controller restrictions - Unsupported configuration Take corrective action based on the above-mentioned reasons and restart the Server Assistant installation process. * Server Assistant does not support RAID configuration on any system with a SATA 2s controller connected to one hard drive. To install Server Assistant on a system with the SATA 2s controller, set the hard drive configuration to "Native Mode" through BIOS or configure RAID through the "Ctrl+A" option. * If a USB flash device is connected to the system, Server Assistant may fail to install the operating system. To resolve the issue, perform one of the following actions: - Remove the USB flash device. - In the BIOS setup, under "Boot Order," move the "USB Device" selection to the end of the list. * The "View Hardware" feature in Server Assistant does not provide information on devices that are connected to the chassis. The current listing of devices is not complete and does not include a few devices such as Fibre Channel cards, Remote Access Controller (RAC) 5. * On PowerEdge 1800 the "View Hardware" feature in Server Assistant does not show the CERC SATA 2s device when it is set to ATA mode. This is due to the current limitation of CERC SATA 2s; it has the same PCI device ID for both ATA and RAID mode. * Use of localized special characters may cause the Server Assistant GUI to freeze intermittently. * If there are multiple SCSI or RAID controllers on the system, Server Assistant will always use the controller listed first in the BIOS boot order list. If you want to use a particular controller for the operating system, set up the given controller as the first boot device in BIOS setup. * Server Assistant does not support the configuration of partitions or the installation of operating systems on systems with PERC 2/SC, PERC 2/DC, or PERC 2/QC controllers or any type of Fibre Channel storage adapter. * It is not recommended to start the server setup program if any virtual disks are in a failed or degraded state. Use the RAID controller's firmware utility (, , or during boot) to reset the RAID controller's state. If an array disk is removed, the firmware utility may indicate the configuration has changed. Accepting these changes on the command line may not be enough; enter the firmware utility and reset the controller. * On CERC ATA or CERC SATA RAID controller cards, disks that appear in "Legacy" mode will not be available for RAID configuration in Server Assistant. If you want to use any disk that is in "Legacy" mode as part of a RAID container, you need to use the RAID controller firmware utility to initialize these disks. Similarly, if all disks are in "Legacy" mode, then Server Assistant may fail to configure RAID on the controller. * The Server Setup program might fail if it runs when scrubbing is active on a RAID virtual disk. * Server Assistant does not identify the boot device when PERC 4/DC or PERC 3/DC are in cluster mode and the adapter's BIOS is disabled. This will put Server Assistant in an infinite "Write Disk signature" and reboot loop. Use Server Assistant to install the operating system on these PERC cards in a non-cluster mode. * Server Assistant cannot detect the correct slot number of the PCI slots containing Adaptec RAID controllers. The message "Unknown Slot Number" is displayed. * On systems with low memory (less than 256 MB) and more than one RAID controller, Server Assistant may fail during RAID configuration. Install the additional adapters after the operating system has been installed on the first adapter. * When using the Custom install script feature, commands that do not return cause the system to stop responding during booting of Red Hat Enterprise Linux or while registering components on Windows installations. * On SAS 5/iR controller cards, disks that appear in "Foreign" state will not be available for operating system installation in non-RAID mode. If you want to use any disk that is in "Foreign" state for the operating system installation, clear the physical disks using "Erase All Physical Disks" feature under System Tools section. If all disks are in "Foreign" state, Server Assistant may fail to install the operating system on the controller in the non-RAID mode. * On system with SAS 5/iR controller cards connected to more than two disks, Server Assistant supports only Advanced RAID Configuration. In "Advanced" mode, it is mandatory to select the disk with the lowest drive ID for RAID configuration. ====================================================================== KNOWN ISSUES FOR RED HAT ENTERPRISE LINUX OPERATING SYSTEMS ====================================================================== * When using the "Dell PowerEdge Installation and Server Management" CD for new RAID configurations, installation of the Red Hat Enterprise Linux operating system may fail if both the USB CD and USB floppy are connected. To avoid the installation failure, remove the USB floppy connection before rebooting the system with the CD for the installation process. * Installation of Red Hat Enterprise Linux (version 4) operating system is not supported on any system having the CERC ATA 4ch controllers: NOTE: In the above case, the option to install Red Hat Enterprise Linux (version 4) will not be available on the "Select Operating Systems" page. * Installation of Red Hat Enterprise Linux (all versions) operating system is not supported on any system having the following controllers (irrespective of being present as boot-controllers or not): * Promise RAID * CERC SATA 2s in RAID mode NOTE: In the above cases, option to install Red Hat Enterprise Linux operating system will not be available on the "Select Operating Systems" page. * The Red Hat Enterprise Linux version 3) operating system installation may fail on systems equipped with multiple RAID and/or SCSI controllers, whether installed on the system board or in PCI slots. This failure may occur when using Server Setup or performing a manual installation. When two or more RAID or SCSI controllers are present, install Red Hat Enterprise Linux with only one configured RAID or SCSI controller. Configure the other controllers after you install the Red Hat Enterprise Linux operating system. * On the Red Hat Enterprise Linux (version 3) operating system, the GUI is not available on the PowerEdge 6800 or PowerEdge 6850 system. This is fixed in the latest update to the "X server" package that is available from Red Hat. Use the Red Hat system update tools to download and install the latest operating system updates. ====================================================================== KNOWN ISSUES FOR SUSE LINUX ENTERPRISE SERVER (VERSIONS 9 and 10) OPERATING SYSTEMS ====================================================================== * The SUSE Linux Enterprise Server (versions 9 and 10) operating system installation may fail on systems equipped with multiple RAID and/or SCSI controllers, whether installed on the system board or in PCI slots. This failure may occur when using Server Setup or performing a manual installation. When two or more RAID or SCSI controllers are present, install SUSE Linux Enterprise Server (version 9 or version 10) with only one configured RAID or SCSI controller. Configure the other controllers after you install the SUSE Linux Enterprise Server (version 9 or version 10) operating system. * The SUSE Linux Enterprise Server (version 9) operating system installation may fail on systems equipped with multiple disks and the boot device is set to a disk that does not have the lowest port number. To ensure successful installation across all supported operating systems, it is recommended that the boot device is set to the disk with the lowest port number. ###################################################################### Information in this document is subject to change without notice. (C) 2006 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: "Dell," "PowerEdge," and "Dell OpenManage" are trademarks of Dell Inc.; "Microsoft," "Windows," and "Windows Server" are registered trademarks of Microsoft Corporation; "Novell" and "SUSE" are registered trademarks of Novell, Inc.; "Intel" is a registered trademark of Intel Corporation; "Red Hat" is a registered trademark of Red Hat, Inc; Conexant is a registered trademark of Conexant Inc. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own. July 2006