FILE NAME:	CP035581

TITLE:		HPE Broadcom NetXtreme-E Online Firmware Upgrade Utility for VMware

VERSION:	5.7.10

REVISION:	0

LANGUAGE:	English

CATEGORY:	Software Solutions

DIVISIONS:	Enterprise and Mainstream Servers

EFFECTIVE DATE:	01/23/2019


Products Affected
==================
HPE Ethernet 10/25Gb 2-port 631FLR-SFP28 Adapter
HPE Ethernet 10/25Gb 2-port 631SFP28 Adapter
HPE Ethernet 10Gb 2-port 535T Adapter
HPE Ethernet 10Gb 2-port 535FLR-T Adapter

Operating Systems
==================
Esxi 6.0
Esxi 6.5
Esxi 6.7

Pre-requisites
===============
ProLiant server supporting above operating systems

Description
============
This package contains the utilities and binaries for upgrading
firmware (boot code, PXE, UEFI, NCSI and CCM code) on HPE Ethernet 
networking adapters (Broadcom NXE controller based) connected to 
supporting Proliant servers running supported ESXi OS.

This component contains combo image version 214.0.203000. The combo image includes: 
Boot Code: v214.0.202.0; NCSI: v214.0.203.0; PXE: v214.0.181.0; UEFI: v214.0.182.0; CCM: v214.0.166.0; RoCE: v214.0.182.0.
The users will only see the combo image versions in the interactive mode firmware update 
or while using HPSUM/SPP to update the firmware on the supported adapters.


Enhancements/Fixes
===================
- Enhancements Description:
  - N/A

- Fixes Description:
  - N/A

Table of Contents
=================
Introduction
Packaging
Performing the Firmware Upgrade
Firmware Upgrade Log

Introduction
============
This file describes the procedure to use for upgrading firmware on 
HPE Ethernet networking adapters mentioned in the 'PRODUCTS AFFECTED'
section of this document.

User guides and additional HPE network adapter information can be found at:
https://www.hpe.com/us/en/servers/networking.html
 
Packaging
=========
The firmware upgrade utility is released in scexe format. The file is a single self-extracting executable that unpacks the component, runs it, and cleans up.

Performing the Firmware Upgrade
===============================
Off-line: 
-------	
SPP Off-line mode boots a special Linux OS environment, thus the Linux Smart Components are used, not the VMware Smart Components  

Remote On-line: If the component is supported by HP SUM but is not yet part of an SPP:
---------------
Download the appropriate SPP	
Add the component to the SPP	
Mount the SPP on a remote server running Windows or Linux that has a network connection to the ESXi host to be updated
Run HP SUM	
Add the ESXi host to be updated as a remote target/node 
Enter IP or DNS address of the ESXi host to be updated 
Enter the ESXi host credentials (root or administrator username and password) 
For HP SUM 6.0 and newer, select both the Additional Package with the added component and the SPP Baseline on the node Inventory page.
Follow HP Smart Update Manager Steps to complete the firmware update
Refer to the SPP documentation for detailed instructions at:www.hp.com/go/spp 

To use HP Insight Control for vCenter: 
-------------------------------------
Log in to the vSphere Client 	
Select a server or cluster in the inventory tree 
Click the HP Insight Management tab	
Follow Insight Control for vCenter steps to update firmware using a Smart Component 

To update firmware from VMware ESXi operating system on target server: 
---------------------------------------------------------------------
 - Enable Tech Support Mode on the ESXi host					
 - Login as root. (You must be root in order to apply the update) 					
 - Place the Smart Component zip file in a temporary directory					
 - Unzip the file CPXXXXXX.zip	
 - Ensure that CPXXXXXX.vmexe is executable by using the command:
 - chmod  +x  CPXXXXXX.vmexe				
 - From the same directory, execute the Smart Component. For example: ./CPXXXXXX.vmexe 					
 - Follow the directions given by the Smart Component 					
 - Logout					
 - Disable Tech Support Mode on the ESXi host	

Firmware Upgrade Log
====================
Results of the firmware upgrade are written to /var/cpq/CPxxxxxx.log.

Important Information
======================
1) The adapter's ethernet interfaces may be down temporarily during the update process.
So any remote sessions via these interfaces will be disconnected temporarily.
2) The Device ID will change when NPAR (NIC Partitioning) mode is enabled. Accordingly 
adapters with DID 0x16D7 and 0x16D8 will change to 0x16EC and 0x16EE respectively if  
NPAR is enabled but RoCE is disabled and to 0x16ED and 0x16EF respectively if NPAR is 
enabled and RoCE is also enabled.

Copyright 2019 Hewlett Packard Enterprise Development LP.
Product names mentioned herein may be trademarks and/or registered trademarks
of their respective companies.
