
          HP MPIO Full Featured DSM for MSA1000/1500 Disk Arrays
                                v1.00.02

                            READ THIS FIRST
                            ---------------


Thank  you  for choosing  HP  MPIO Full Featured DSM  for  MSA1000/1500 
Disk Arrays.

Please  read  the  following information before installing this release
of the DSM.


***********************************************************************

I.    Contents
II.   Introduction
III.  System Requirements
IV.   Installing HP MPIO Full Featured DSM for MSA1000/1500 Disk Arrays
V.    Uninstalling HP MPIO Full Featured DSM for MSA1000/1500 Disk
      Arrays
VI.   Limitations/Known Issues
VII.  Notes
VIII. Changes
IX.   Contact Information

***********************************************************************

I.   Contents

     The installation media (CD) should contain the following:

         * READ THIS FIRST release information (readme.txt)
         * Setup files
         * User manual


II.  Introduction

     HP  MPIO  Full  Featured DSM (Device Specific Module) for MSA1000/
     1500 disk arrays provides multipathing support for HP StorageWorks
     MSA1000/1500 disk arrays on Windows 2000 and higher platforms.  It
     is based  on  the Microsoft MPIO framework  and  provides features
     such  as  I/O  load  balancing,  path  failover and path recovery/
     failback.

     This package contains the following components:

         * Microsoft MPIO framework
         * HP Device Specific Module (DSM) for MSA1000/1500 disk arrays
         * Command Line Interface (CLI)
         * Performance Provider DLL for Windows Performance Monitor


III. System Requirements

     System requirements  for installing  HP MPIO Full Featured DSM for
     Windows for MSA1000/1500 disk arrays are as follows:

         * Supported platforms:

          - Windows 2000 Server and Advanced Server with Service Pack 4
          - Windows Server 2003 with Service Pack 2 (x86, IA64 and x64)
          - Windows Server 2003 R2 with Service Pack2 (x86,x64)          

         * 40 MB (approx.) free disk space.
         * HP StorageWorks  MSA1000/1500  disk  arrays running firmware 
           version 6.x or above and configured with logical devices.
         * Supported  Fibre  Channel  Host Bus Adapters (HBA) with  the
           supported HBA driver and firmware installed.

     For details  on supported  HBAs, HBA driver and firmware versions,
     please contact HP support.


IV.  Installing HP MPIO Full Featured DSM for MSA1000/1500 Disk Arrays

     Ensure  that  the  system  meets  the  minimum requirements before
     installing this product(refer Section III).

     It is recommended  to close all  open programs  before  proceeding
     with the install/modify/repair options of this package.

         1. To begin installation, log on as an administrator user.
         2. Insert  the HP MPIO Full Featured DSM for MSA1000/1500 Disk
            Arrays CD into the selected drive.
         3. If  autorun  is  enabled,  HP  MPIO  Full  Featured DSM for
            Windows  for  MSA1000/1500  Disk  Arrays  Setup  will start 
            automatically.
            Otherwise, run  setup  from  x:\Launch.exe, where x: is the
            drive letter where the installation media has been inserted.
         4. Follow on-screen instructions to complete the installation.


V.   Uninstalling HP MPIO Full Featured DSM for MSA1000/1500 Disk Arrays

     Follow the steps below for uninstallation:

         1. Disconnect  the  redundant paths  to  all HP  StorageWorks
            MSA devices supported by this product.
         2. Select Start menu --> Settings --> Control Panel.
         3. Double click "Add/Remove Programs".
         4. Under "Add/Remove Programs",  select "HP MPIO Full Featured
            DSM  for MSA1000/1500 disk arrays v1.00.02"  and  click the
            Remove button.
         5. Follow on-screen instructions to complete uninstallation.


VI.  Limitations/Known Issues

         1. The  devices  should be presented on all paths to the host.
            (selective presentation of devices on specific  host  paths
            is  not supported).
         2. On any one host, all Host Bus Adapters  must be of the same
            type.
         3. For cluster environments, only Microsoft Cluster Service is
            supported.
         4. When you configure a new server  cluster on a computer that
            is running  Windows Server 2003,  the  cluster software may
            not automatically  bind to the  shared disks. To workaround
            this issue,  turn off  load balancing  on the  shared disks
            before starting the installation of the new server cluster.
         5. Load balancing is not supported in a cluster environment.
         6. It  is  recommended  to  install  HP MPIO Full Featured DSM
            for MSA1000/1500 Disk Arrays before installing the Microsoft
            Cluster Service.


VII. Notes

         1. For  details  about  the  MPIO  framework  included in this
            package, please refer the Release Notes.
         2. For Silent installation:
            If the  current  MPIO  framework in the sytem is newer than
            the  one  included  in  this  package,  the  default silent
            installation file new.iss has to be modified such that  the
            MPIO framework component is unselected during installation.
            For details on how to do this, see the  silent installation
            section in the Installation & Reference Guide.
            
            
VIII. Changes

         1. Updated to MPIO framework v1.18
         2. Added  support  for  handling  the  HBA removals (performed
            either via hot-plug functionality or through Windows Device
            Manager).
         3. Addressed an issue  specific to  64-bit platforms where the
            use of SQST  load balancing  policy  did not always use all
            available paths.
            

IX.  Contact Information

     To  learn more about HP  and  HP  products, services  and support,
     visit the HP web site at http://www.hp.com.

     For  FAQs, software  updates,  and  contact  information  for  HP
     products, visit the HP Support Home Page at
     http://www.hp.com/go/storage.

--End--